Cut Piece Dustproof Separating Agent, Anti-Sticking Emulsion For Shoe Rubber Cut Parts

Model:SEP-EMU-01 

Specification	Parameter Details
Product Form	Milky white water-based emulsion, low viscosity liquid
Net Volume Per Bucket	20L HDPE plastic bucket
Active Content	22%~25%
pH Value	6.5 ~ 8.0 (Weakly neutral)
Applicable Materials	Natural rubber sheet, compound rubber slab, rubber sole cut pieces, EVA foaming sheets, TPR raw sheets
Application Method	Spraying / Dipping / Wiping
Drying Condition	Natural air drying or low-temperature drying 40~60℃
Standard Packing	20L per plastic pail
Pail Dimension (L×W×H)	310×310×385 mm
Pail Net Weight	20.5 KG
Pail Gross Weight	21.3 KG

Cut Piece Dustproof Separating Agent

Formulated as water-based eco-friendly emulsion with low VOC and low odor, this separating agent contains no pungent solvents. It delivers outstanding anti-sticking performance to separate stacked rubber sole cuttings and prevent adhesion between die-cut rubber sheets. It also provides reliable dustproof capability by forming a thin isolating film on rubber surfaces and lowering dust absorption during storage. The product does not interfere with follow-up vulcanization, adhesion and surface finishing processes of rubber soles. 

It creates a thin transparent barrier without white powder precipitation, preventing surface blooming and contamination of shoe materials. The emulsion supports flexible dilution; users can adjust concentration according to production rate and storage duration. Spraying equipment can be easily cleaned with plain water without stubborn scaling. 

Featuring non-corrosive composition, it protects operators and will not erode the surface of rubber raw materials. Specially tailored for shoe material manufacturers and rubber sole cutting workshops, this dustproof separating emulsion serves multiple industries. Within the footwear sector, it offers isolation and anti-sticking protection for rubber outsole cuttings, natural rubber sheets, compound rubber slabs, TPR sheets and pre-cut EVA foamed materials. Rubber processing plants apply it for stacking separation of unvulcanized rubber blanks, rubber strips and molded rubber semi-finished goods. Foam processors utilize it for temporary isolation of EVA and PE foamed sheets during turnover and storage. It is also suitable for anti-adhesion storage protection of semi-finished rubber gasket cuttings in the hardware and sealing industry.

Thoroughly stir the emulsion before use. It can be diluted with clean water at a ratio of 1:1 ~ 1:3 depending on working conditions. Apply even low-pressure spraying onto one side of rubber cut pieces; excessive dosage should be avoided to prevent thick film buildup. Ensure full surface drying before stacking rubber soles to obtain optimal anti-sticking results. 

Filter diluted liquid before filling spraying equipment to prevent nozzle blockage from fine impurities. Rinse spray guns and pipelines with clean water after daily work to avoid emulsion solidification and clogging. Adopting solvent-free water-based composition, the product meets international low-VOC footwear standards, improving workshop air quality and safeguarding staff health. 

Optimized manufacturing processes cut solvent waste compared with conventional oil-based separators, and all factory wastewater undergoes sedimentation treatment before discharge. Packed in recyclable HDPE plastic pails, empty containers can be recovered and reused to reduce single-use plastic waste. We promote lean production concepts for downstream shoe factories, helping minimize rejects caused by rubber adhesion and lower raw material loss. Complete MSDS documents are supplied to standardize chemical handling and ensure occupational safety. 

This is a water-based emulsion rather than oil-based products. It has low odor and eco-friendly features and maintains compatibility with subsequent vulcanization procedures. The advanced formula generates no white precipitates to eliminate blooming contamination on shoe materials. It is primarily developed for anti-sticking and dust protection of unvulcanized rubber sole cuttings. Pure water dilution is available with adjustable proportions from 1:1 to 1:3 according to production demands. For prolonged shelf life, keep the product sealed in cool storage away from direct sunlight and freezing conditions. Apart from rubber products, it is compatible with semi-finished cut pieces of EVA, TPR and various shoe materials.